Tips to Taking Good Care of Your Bicycle
Lubricating the moving parts
You should do this oftenly but using an appropriate amount of lubricant. Little and often is the way to go when it comes to lubricating your bike. Parts like the chain, gear shifter, brakes and in between the wires in the tyres should be oiled. Lubrication depends on how much you use your bike.
Stretch cables to bring back tension
This process is a bit technical but will greatly improve the overall performance of your bike. With time the inner gears and brake cables tend to stretch and you'll find that pressing the brakes will not function with a quick response. Same applies to the shifting gear cables which will be faulty. So this is a very important maintenance tip for your bicycle. To know which is best for you, read some Rovo Bike Reviews.
Do not leave your bike outside all the time
A bike is generally made up of metal parts that will spoil when they come into contact with water especially the kind near the sea. The high salt content corrodes the metal parts as time passes. Keeping the bike inside when it's not in use is the very best solution for this problem. Try to take your bike for a spin once in a while to prevent it's gears and brakes from seizing up.
Pump up the tyres
The single biggest positive impact you can have on your riding experience is having fully inflated tyres. Properly pumped tyres are less prone to punctures, and by absorbing bumps and shocks, they reduce wheel damage. Pumping up your tyres is an easy task that doesn't consume a lot of your time. The reviews about these bikes are found at rovobikereviews.com.
Clean and grease your seatpost
Do this by marking your seat's height with a piece of tape by wrapping the tape around the post right where it meets the frame then remove the post and wipe it off with a clean rag. After this jam that rag down into the seat tube as far as you can and pull it out. Smear some grease inside the seat tube and slide the post back into the frame up to the tape line after which you should tighten the clamp. You can use grease.
Cleaning
It's no rocket science that if you ride your bike regularly it's bound to get dirty. Dirt, sand and mud will cause parts of your bike to wear out quickly. When these parts are worn out then they compromise the full functionality of the bicycle. Wash your bike after long rides, or as frequently as you can using warm soapy water, rags and brushes that will enable you to scrub the dirt, and scum from the stubborn areas. Watch https://www.youtube.com/watch?v=swhOwaWZu8U for more info about road bikes.
Lubricating the moving parts
You should do this oftenly but using an appropriate amount of lubricant. Little and often is the way to go when it comes to lubricating your bike. Parts like the chain, gear shifter, brakes and in between the wires in the tyres should be oiled. Lubrication depends on how much you use your bike.
Stretch cables to bring back tension
This process is a bit technical but will greatly improve the overall performance of your bike. With time the inner gears and brake cables tend to stretch and you'll find that pressing the brakes will not function with a quick response. Same applies to the shifting gear cables which will be faulty. So this is a very important maintenance tip for your bicycle. To know which is best for you, read some Rovo Bike Reviews.
Do not leave your bike outside all the time
A bike is generally made up of metal parts that will spoil when they come into contact with water especially the kind near the sea. The high salt content corrodes the metal parts as time passes. Keeping the bike inside when it's not in use is the very best solution for this problem. Try to take your bike for a spin once in a while to prevent it's gears and brakes from seizing up.
Pump up the tyres
The single biggest positive impact you can have on your riding experience is having fully inflated tyres. Properly pumped tyres are less prone to punctures, and by absorbing bumps and shocks, they reduce wheel damage. Pumping up your tyres is an easy task that doesn't consume a lot of your time. The reviews about these bikes are found at rovobikereviews.com.
Clean and grease your seatpost
Do this by marking your seat's height with a piece of tape by wrapping the tape around the post right where it meets the frame then remove the post and wipe it off with a clean rag. After this jam that rag down into the seat tube as far as you can and pull it out. Smear some grease inside the seat tube and slide the post back into the frame up to the tape line after which you should tighten the clamp. You can use grease.
Cleaning
It's no rocket science that if you ride your bike regularly it's bound to get dirty. Dirt, sand and mud will cause parts of your bike to wear out quickly. When these parts are worn out then they compromise the full functionality of the bicycle. Wash your bike after long rides, or as frequently as you can using warm soapy water, rags and brushes that will enable you to scrub the dirt, and scum from the stubborn areas. Watch https://www.youtube.com/watch?v=swhOwaWZu8U for more info about road bikes.